Can the H9 sum the two Mono inputs before effecting them?

Home › Forums › Products › Stompboxes › Can the H9 sum the two Mono inputs before effecting them?

Tagged: 

  • This topic is empty.
Viewing 6 reply threads
  • Author
    Posts
    • February 1, 2020 at 1:20 pm #115742
      FrankvonWelt
      Participant

      Hi folks,

      I use my H9 max with synthesizers. In a live situation I have two Mono synths i would like to run thru the H9. And I would love to just hook up both to the H9 before sending the stereo out to a mixer. Is there a way to mix the 2 Mono to one stereo signal pre FX ? I already saw similar questions here. But no real solution. And the routing options in the general settings seem not to be able to do this.

      Thank you.

      Frank

    • February 1, 2020 at 8:44 pm #153978
      bohan
      Moderator
      Eventide Staff
      FrankvonWelt wrote:
      Hi folks, I use my H9 max with synthesizers. In a live situation I have two Mono synths i would like to run thru the H9. And I would love to just hook up both to the H9 before sending the stereo out to a mixer. Is there a way to mix the 2 Mono to one stereo signal pre FX ? I already saw similar questions here. But no real solution. And the routing options in the general settings seem not to be able to do this. Thank you. Frank

      If you just want to sum the two mono inputs, you would need a mixer or something similar. You can also plug 2 synths into the input 1 & 2 jacks of the H9. But in this case the effect applied to both inputs might be different. For example, if the Delay Mix or Pitch Mix is at A10+B10, the Delay/Pitch A will affect the input 1, and the Delay/Pitch B will affect the input 2

    • February 1, 2020 at 9:17 pm #153979
      FrankvonWelt
      Participant

      Mh yes Plugin both in will not be the Same .. at the end Synth 1 will be on the left only. Synth 2 on the right only … and it depends on the the defect if some material from synth 1‘s wet Signal will be heated on the other side ..
      i know an external mixer would do the job but I don’t wanna carry 2 mixers and avoid extra gear just for such a „tiny“ purpose .. maybe Eventide will add this to a future firmware ..

    • February 2, 2020 at 1:10 pm #153986
      Fender17
      Participant

      You could use sort of fixed “mixing” cable. Two Y cables might do. Or EHX Stereo pedal might be cool. You could do dynamic panning of synths…..

    • February 15, 2020 at 3:39 am #154073
      davebrubaker
      Participant

      Saturn Works has a cheap sum mixer pedal with volume controls. It’s about the size of a mini pedal.

    • February 16, 2020 at 4:08 pm #154078
      PhaseShift
      Participant

      technically, the Looper ALgo, does Sum the L & R inputs to Mono to record the loop, and then doubles the Mono Signal onto the L & R channels, so this should be possible through firmware, but seeing the staff answer above does make sense too.

      I really feel this might be possible though.

    • February 17, 2020 at 4:33 pm #154088
      bohan
      Moderator
      Eventide Staff

      Would something like these work for you? I'm not 100% sure.

      https://www.sweetwater.com/store/detail/CYP103–hosa-cyp-103-y-cable-1-4-inch-ts-to-dual-1-4-inch-ts-3-foot

      https://www.sweetwater.com/store/detail/YPP111–hosa-ypp-111-y-cable-1-4-inch-ts-to-dual-1-4-inch-tsf-6-inch

    • February 16, 2020 at 6:10 pm #154079
      FrankvonWelt
      Participant
      bohan wrote:
      FrankvonWelt wrote:
      Hi folks, I use my H9 max with synthesizers. In a live situation I have two Mono synths i would like to run thru the H9. And I would love to just hook up both to the H9 before sending the stereo out to a mixer. Is there a way to mix the 2 Mono to one stereo signal pre FX ? I already saw similar questions here. But no real solution. And the routing options in the general settings seem not to be able to do this. Thank you. Frank

      If you just want to sum the two mono inputs, you would need a mixer or something similar. You can also plug 2 synths into the input 1 & 2 jacks of the H9. But in this case the effect applied to both inputs might be different. For example, if the Delay Mix or Pitch Mix is at A10+B10, the Delay/Pitch A will affect the input 1, and the Delay/Pitch B will affect the input 2

      Thank you. No it’s not just mixing. But at the moment i will hear one synth only on the left side and the other one only on the right side. (Plus maybe some stereo wet signal on the stereo out. It would just be nice to center them both at the stereo output before effecting them.
      I know that an extra mixer will solve this problem but in a Club the room I get is always limited and I don’t wanna carry a second mixer with me just for this use case. Let’s say I ask for this as a feature request. Maybe you consider to do this one day in a future firmware update.

    • February 16, 2020 at 6:12 pm #154080
      FrankvonWelt
      Participant
      PhaseShift wrote:
      I really feel this might be possible though.

      So do I 🙂

  • Author
    Posts
Viewing 6 reply threads
  • You must be logged in to reply to this topic.