ModFactor Software 2.4.2[1] Available

Eventide is happy to announce the availability of ModFactor 2.4.2[1] Software. This update includes extensions
to ModFactor’s operating system which improve compatibility with TimeFactor
and PitchFactor. We recommend that you only install this software when you have
time to become familiar with it and never just before a tour or gig.

We strongly recommend that you back up your existing presets before updating
to a new software version.

For information on backing up Presets, visit the ModFactor
Support Page.

Reverting to Previous Software

Note that it is possible to revert to the original version anytime. However,
reverting from 2.4.2[1] to version 2.0.2[3] will require a clear setup, which
can be executed by booting up while simultaneously holding the Encoder and Tap
switch. After clearing setup you will have to restore system settings to your
liking. Although this process will not erase your presets, we recommend you
backup any presets prior to updating.

How to Update

Updating requires the following steps:

1. Create
   an Eventide.com Account.
2. Register
   your ModFactor Pedal.
3. Download and Install the Eventide Update Utility from the ModFactor
   Support Page.

   You will not be able to download this utility until you have successfully
   logged in to Eventide.com and registered your ModFactor.

4. Connect your ModFactor Pedal to your computer using a standard USB Cable
   (not provided by Eventide).
5. Launch the Eventide Update Utility Application. Please be patient, as it
   can sometimes take up to 1 minute to recognize the ModFactor Pedal.
6. Select the System Version 2.4.2[1] from the Available Updates list and click
   the Update button.
7. When prompted for a username and password, enter your Eventide.com username
   and password.
8. Review the Release Notes and License Agreement displayed by the Eventide
   Update Utility.
9. Wait for the Update to Complete. This usually takes a few minutes.

Troubleshooting Tips

• Verify that you have properly registered your ModFactor pedal, and that
  your username and password are correct. This can easily be done by viewing
  the My Products page. In order for the update to succeed, the Serial Number
  on your ModFactor pedal must appear on this list, and you must supply the
  same username and password used to access the My
  Products page when prompted by the Eventide Update Utility.
• If the update is started but does not complete successfully, the pedal may
  not function properly. If the pedal does not properly start up, the Eventide
  Update Utility will not be able to communicate with it. In this case, it will
  be necessary to force the pedal into Update Mode by holding down the center
  switch while applying power. Once the word "UPDATE" appears on the
  display, restart the Eventide Update Utility and attempt the update again.
• For additional tips, visit
  this forum page.

ModFactor Update Release Notes

Fixes In Version 2.4.2[1]

MIDI CC messages are no longer affected by having Catchup ON.

The default Expression Pedal assignment for new Factory Presets is Speed.

Expression Pedal assignments for original Factory Presets have been corrected.

An issue has been fixed where some Knobs were not saving properly.

Setting FS3 to be controlled by Aux Switch T+R now works correctly.

The LFO Display now works.

The Q-Wah Type Knob display is now correct.

Previous Changes from Version 2.4.1[1]

More Presets

ModFactor now supports up to 50 Banks/100 Presets. The number of banks in the
UTILITY menu may need to be increased to make these visible.

This update includes killer new factory presets.

New Chorus Type

A new Chorus algorithm, “Classic,” has been added to the Chorus Type
knob. The Xnob acts as a filter to dial in a wide variety of warmer, vintage
style chorus sounds.

New Phaser Type

A new Phaser algorithm, “PhaseX0,” has been added to the Phaser Type
knob. The Xnob can switch between 2, 4, 6, and 8 Stages to provide a larger
assortment of classic phaser sounds.

Output Level Knob in Rotary

The Rotary Effect now uses the Intensity knob as an output level control.

Expression Pedal Improvements

Expression Pedal Programming Activation

Expression Pedal programming is now activated only when the Expression Pedal
is at the heel or toe position.

Shorter Timeout

The Pedal Programming Timeout has been reduced to 2 seconds. This means that
when you move the Expression Pedal to heel or toe position, ModFactor will allow
Expression Pedal programming for 2 seconds and then change to normal operation.

Pedal Programming Lock

You can now optionally disable live Expression Pedal programming. (See System
Menu Updates.)

Parameter Fine-Tuning

The Encoder can now be used to fine-tune all knob parameters if turned within
2 seconds of turning any knob.

Bank Select via Encoder Knob

In Bank Mode, the Encoder can now be used to select banks in either direction
if turned within 2 seconds of pressing a bank change footswitch.

System Menu Updates

[MIDI] – General Improvements have been made to MIDI operation, including
these new MIDI Functions:

[RCV CTL] – There are new choices for Receive Control to alter the unit’s
BYPASS setting:

ACT – Make the unit ACTive, i.e. not bypassed.

TOG – TOGgle the between bypass and active.

[RCV MAP] – BYPASS via Program Change

As well as using MIDI program change to load a preset, now it can also be
programmed to directly control the unit’s BYPASS setting. In the Receive
Map menu you can now select one of the following:

BYP – BYPass the unit

ACT – Make the unit ACTive, i.e. not bypassed.

TOG – TOGgle the between bypass and active.

[CLK IN] – MIDI Input Clock Enable

Turn Encoder to set MIDI Clock Receive ON or OFF. If ON, MIDI Clock is used
as a Tempo source.

[CLK OUT] – MIDI Output Clock Enable

Turn Encoder to set MIDI Clock Transmit ON or OFF. If ON,

ModFactor can now be used as a MIDI Clock source.

[CLK FLT] – MIDI Clock Filter Enable

Turn Encoder to set MIDI Clock Filtering ON or OFF. If ON,

ModFactor can be used with an unstable MIDI Clock source.

[UTILITY] – New Utility Function:

[PDLOCK] – "Lock" Expression Pedal settings

When PDLOCK is set to ON, Expression Pedal programming is disabled and all
Expression Pedal settings are locked. Default is OFF (unlocked).

Miscellaneous Fixes

MIDI Clock timing has been improved.

The accuracy of using MIDI CC to control TAP has been improved.

A received real time MIDI signal (e.g. MIDIclock) no longer terminates any
sysex message also being received.

Dumping presets over USB no longer results in BAD LOAD messages.

The displays for Tempo and Dly are now consistent among all three Factor series
Stompboxes.

Overall Wet/Dry levels are now more consistent.

In System/MIDI/XMT CC when you change the MIDI CC numbers from factory defaults,
the settings are no longer lost after power cycle.

TremoloPan no longer mutes the signal coming from Input 2.

When using an Aux Switch assigned to TAP, a single tap of the Aux Switch now
displays the current tempo like a single tap on the on-board TAP footswitch
does.

When receiving a MIDI CC set to control the PDL parameter, the audio is now
affected correctly.

When assigning an Aux Switch to P/B, the switch no longer decrements the Bank
number with every other press.

General improvements have been made to speed up the system response.

Previous Changes from Version
2.0.2[3]

Undulator Fixes

An issue has been fixed where Undulator didn't work with Sine Wave selected
under the shape knob. Also,

Intensity now controls Mix in Undulator.

Control Expression Pedal via MIDI CC

In the RCV CTL area of the MIDI menu, PDL is now a choice for something that
will respond to MIDI

Continuous Controller. This allows you to do things like automate an expression
pedal performance from a

computer or use an external MIDI expression pedal to control Preset expression
pedal assignments.

PDL choice in AUX SW Menu

Assigning "PDL" to an Aux Switch allows you to get the full value
of the preset's Expression Pedal

assignment (Toe down) while you hold that switch. This is great for things like
sending feedback to 110%

while holding the switch down and then back to a "safe" value when
you let go.

Default Aux Switch Assignments

The Factory Default Aux Switch assignments are now BYP, RPT, and TAP for TIP,
RNG, and T+R. (You'll

need to Initialize SETUP to get the factory defaults – Hold the Encoder button
and Middle footswitch on

power up).